Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Beverly Hills, CA
Gate repair in Beverly Hills usually splits into two jobs: restoring the gate itself, and restoring the automation and access system that controls it. On the hillside streets north of Sunset and in Trousdale Estates, we routinely work on custom-fabricated iron gates tied into Crestron or Control4 platforms, where a gate that won’t open is rarely just a mechanical failure. Call (213) 577-1120 and a live person answers, any hour.
Why Beverly Hills Homes Are Different
The gates here are not off-the-shelf. The flats south of Santa Monica Boulevard hold Spanish Colonial and Tudor estates from the 1920s through the 1950s with ornamental wrought-iron swing gates on tight setbacks, while the hillside streets and Trousdale Estates hold mid-century and contemporary homes with long driveway slide gates on sloped grades. Those two scenarios fail differently. A wrought-iron swing gate on a flat lot typically wears out hinges and latch hardware over decades. A long slide gate on a 10 to 15 percent grade overloads motors, seizes rollers, and creeps or slams under gravity load if the operator limits were not set correctly. The prolonged dry season adds fine dust and eucalyptus debris that packs into tracks and rollers without warning, and the fall Santa Ana winds put exceptional stress on large swing gates on exposed canyon-facing properties, bending hinges and overloading operators sized for calm conditions. Beverly Hills Building & Safety requires permits for any motor replacement or structural modification, and inspectors specifically scrutinize operator settings on hillside driveways during final inspection.
Our Main Beverly Hills Services
Most homeowners call us for one of three reasons: the gate has stopped moving, the gate needs to be replaced or built new, or the motor and opener are failing. Each has its own Beverly Hills page with local pricing and detail.
Gate Repair in Beverly Hills
This covers the gate itself: hinges, rollers, posts, weld cracks, sagging leaves, latch hardware. On a 1920s Spanish Colonial with original ironwork, we often find hinge pins worn oval and posts pulling out of stucco piers. On a Trousdale slide gate, we more often find seized rollers and a track packed with dust. The full breakdown lives on the Gate Repair in Beverly Hills page.
Gate Installation in Beverly Hills
New gates in Beverly Hills are typically custom-fabricated to match the architecture, then integrated with an automation system and often a whole-home platform. On hillside lots, that means engineering for wind load and grade. The Gate Installation in Beverly Hills page covers permits, materials, and what a full installation includes.
Gate Motor & Opener in Beverly Hills
Motor and opener work here frequently involves matching a new operator to a gate that was fabricated decades before the operator existed. We service what is already on the property, including FAAC, BFT, Linear, and Viking, rather than steering toward replacement. See Gate Motor & Opener in Beverly Hills for the full scope.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Beverly Hills
Gate access control in Beverly Hills is less about bolting on a keypad and more about integrating whatever entry method you choose with a gate that already talks to a Crestron or Control4 system. We see this most on hillside properties where the gate sits far from the house, and on older estates where an intercom or keypad was added years after the original gate went in. The Gate Access Control work we do here runs from simple keypad replacement to full phone-entry and video-intercom integration.
Keypad Entry
Signs you need it
The keypad works intermittently, the buttons stick, or the code stopped accepting after a power outage.
What it costs in Beverly Hills
Keypad replacement in Beverly Hills typically runs $280 to $620 installed, depending on weather rating and whether the wiring needs to be pulled new.
How we do it
We match the voltage and protocol to the existing operator, mount the keypad in a weather-protected position, program codes, and photograph the finished install.
Video Intercom
Signs you need it
The video feed is dead, audio is one-way, or the exterior station is failing after years of direct sun exposure.
What it costs in Beverly Hills
A Beverly Hills video intercom replacement typically ranges $750 to $1,500 depending on the existing wiring and whether you want app-based remote answering.
How we do it
We test the existing cable run first, swap the station and monitor or app bridge, re-terminate connections, and leave a photo record of the setup.
What Gate Access Control Costs in Beverly Hills
| Item | Typical range in Beverly Hills |
|---|---|
| Keypad replacement | $280 - $620 |
| Video intercom replacement | $750 - $1,500 |
| Phone entry module | $450 - $900 |
Can you integrate access control with my existing Crestron or Control4 system?
Yes. We match the access-control hardware to the integration protocol your automation platform expects, then verify the gate’s own operator limits are set correctly so the system is not fighting a misconfigured motor. Call (213) 577-1120 to walk through your setup.
Do I need a permit for access control work in Beverly Hills?
Access-control hardware alone typically does not require a permit, but any motor replacement or structural modification on the gate does. We confirm the scope with Beverly Hills Building & Safety before quoting, and the written price you approve is the price you pay.
Gate Parts & Welding in Beverly Hills
On Beverly Hills estates, gate parts and welding often means repairing or recreating hardware that was custom-fabricated for a one-of-a-kind gate and has no off-the-shelf equivalent. The flats have ornamental iron from the 1920s through 1950s with hinges and posts that have outlived their original design life, while the hillside gates carry heavy wind and gravity loads that crack welds and bend rails. Our Gate Parts & Welding work here centers on restoring original ironwork and fabricating replacements when no catalog part exists.
Hinge Replacement
Signs you need it
The gate sags, scrapes the ground, or the hinge pins are visibly worn oval and the leaf no longer sits square in the opening.
What it costs in Beverly Hills
Hinge replacement on a Beverly Hills estate gate typically runs $200 to $600 per hinge, depending on whether the post needs reinforcement and whether we match an existing ornamental pattern.
How we do it
We support the gate, cut out the worn hinge, weld in a matched replacement, re-square the leaf, and photograph the new weld before paint.
Custom Welding
Signs you need it
A visible crack has opened in an iron member, a scroll or finial has snapped off, or the gate frame is twisted from a Santa Ana wind event.
What it costs in Beverly Hills
Custom welding and crack repair typically runs $150 to $400 per repair point in Beverly Hills, with fabrication of missing ornamental elements quoted per piece.
How we do it
We grind back to solid metal, weld with matched rod, blend the repair to the original profile, and document the work with before-and-after photos.
What Gate Parts & Welding Costs in Beverly Hills
| Item | Typical range in Beverly Hills |
|---|---|
| Hinge replacement | $200 - $600 per hinge |
| Custom welding repair | $150 - $400 per point |
| Gate roller replacement | $80 - $250 per roller |
Can you match the original ironwork on my 1920s gate?
In most cases, yes. We fabricate replacement scrolls, finials, and rail sections to match the existing profile and then finish the repair so it reads as original. The written quote includes fabrication time before any torch lights.
Do you repair the gate on site or take it to a shop?
Most welding happens on site with a mobile rig. Larger fabrication jobs may go to a shop, but the gate stays hung and functional whenever possible, and you receive a photo record either way.
Brands We Service in Beverly Hills
We service FAAC, BFT, Linear, and Viking operators without steering you toward a replacement. Common control boards, remotes, and photo-eyes ride on our trucks, so many Beverly Hills repairs finish same-day. See our brands for the full list.
Pricing for Gate Repair in Beverly Hills, CA
| Service | Typical range in Beverly Hills |
|---|---|
| Keypad replacement | $280 - $620 |
| Video intercom replacement | $750 - $1,500 |
| Phone entry module | $450 - $900 |
| Hinge replacement | $200 - $600 per hinge |
| Custom welding repair | $150 - $400 per point |
| Gate roller replacement | $80 - $250 per roller |
What pushes price up in Beverly Hills is scale and integration: a long slide gate on a 15 percent grade needs more motor and more travel hardware than a flat-lot swing gate, and a gate tied into Crestron or Control4 adds integration time. Every job gets a written price before we touch a tool, so the number you approve is the number you pay.
Neighborhoods We Serve in Beverly Hills
We work across Beverly Hills, from the flat-lot estates south of Santa Monica Boulevard to the hillside streets and gated compounds north of Sunset. Response times vary with traffic, but our technicians are typically on site within a few hours for non-emergency calls.
- Trousdale Estates
- The Flats
- Beverly Hills Post Office
- The Golden Triangle
- Beverly Crest
Service Area - Cities Near Beverly Hills
Vance Gate Repair serves Beverly Hills and the surrounding communities across the Westside and the Valley. If your gate is in West Hollywood, CA, Studio City, CA, Sherman Oaks, CA, or North Hollywood, CA, the same written-price standard and 365-Day Done Right Promise applies.
Serving Beverly Hills, CA - Our Local Coverage Area
We’re based in the Beverly Hills area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Beverly Hills
For non-emergency calls, we are typically on site within a few hours depending on traffic across the city. Emergency calls get prioritized, and a live person answers the phone at (213) 577-1120 twenty-four hours a day, so there is no callback queue between you and a dispatch.
Repair work on existing hardware, access control, and welding typically does not require a permit. Motor replacement or structural modification does, and Beverly Hills Building & Safety requires an inspector to verify operator settings on hillside driveways during final inspection. We confirm the permit scope before quoting.
Some gated streets and estates in Beverly Hills have architectural review boards or estate managers who must sign off on any visible gate work. We will prepare a written scope of work with part numbers and photos if your HOA needs documentation before approving the repair.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Beverly Hills Customers Say
"The safety loop had never been installed correctly by the previous company. They showed me the reading, fixed it, and did not charge me for the diagnosis."
- Patrick H."Quoted in writing, installed on the day promised, and the price did not move. The crew was licensed and the number was on the paperwork."
- Wes A."Good work on a long driveway gate. Arrived when they said, finished when they said."
- Sofia E.