Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Burbank, CA
Gate access control in Burbank runs into a problem most cities never see: studio campuses with thousands of gate cycles per week right next door to 1940s ranch homes with gates bolted onto concrete that was never meant to hold them. The heat does not help either, with summer temperatures over 100°F cooking circuit boards and stretching ornamental iron until hinges bind. Call (213) 577-1120 and you will get a live person who can dispatch a technician to your Burbank property.
Why Burbank Homes Are Different
Burbank sits in a San Fernando Valley thermal pocket, and the heat is the first thing every gate technician notices here. Operators mounted on black iron gates in full sun run hot enough to fail early, and rubber drive belts crack faster than they do in coastal neighborhoods twenty miles west. The housing stock adds a second layer. Most Burbank flats are 1940s to 1970s ranch-style and bungalow homes where driveway gates were retrofitted decades after the foundation was poured, often without engineered footings. That means posts settle, hinges drift out of alignment, and operators that worked fine for years suddenly strain against a gate that no longer sits square.
Move up into the Burbank Hills near the Verdugo foothills and the job changes again. Sloped driveways put constant downhill pressure on swing gates, so hinges and operators take a beating that flat-lot installs never experience. And when Santa Ana winds rip through the valley mouth in fall and winter, sliding gates get knocked off their bottom rollers and wooden pickets snap with regularity. Knowing which failure mode belongs to which part of Burbank shortens the diagnosis considerably.
Our Main Burbank Services
Most Burbank homeowners call us for one of three things: a gate that will not open, a gate that needs to be designed and installed from scratch, or an operator that has given up. Here is how each one works here.
Gate Repair in Burbank
Repair calls in Burbank split along a predictable line. Flat-lot homes in the Burbank flats deal with post-settling and hinge wear; hillside homes near the Verdugo foothills deal with gravity-driven sag and operator strain. Our techs arrive with a written price handed over before any tool comes out, and every visit ends with a photo log of what was found and what was fixed. Gate Repair in Burbank covers everything from a bent hinge to a gate that will not budge.
Gate Installation in Burbank
New gate installation in Burbank almost always starts with the footing question. Older ranch homes rarely have a concrete base that was poured for a gate, so we plan the post work before the gate itself is ever ordered. On hillside lots, that planning gets more involved: hinge placement, operator sizing, and stop settings all change when the gate swings against a slope. Gate Installation in Burbank includes a free measure and a written price before work begins.
Gate Motor & Opener in Burbank
Burbank heat is unkind to gate operators. Circuit boards fail, capacitors swell, and drive belts crack, which means motor replacement here is a routine job rather than a rare one. We service nine major automation brands, so the conversation starts with what is already on the property instead of a push toward replacement. Gate Motor & Opener in Burbank covers diagnosis, repair, and replacement with a written price up front.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Burbank
Gate access control in Burbank means something specific: homes where privacy is a working requirement, not a preference. Entertainment-industry professionals in neighborhoods near the Warner Bros. perimeter on Olive and the Disney campus on Buena Vista often need keypads, phone entry, or card readers that integrate with a gate, and studio-adjacent properties sometimes require vendor credentials just to reach the gate. Summer heat accelerates failures in exposed keypads and intercom boards, and hillside wireless signals from the Verdugo foothills create range problems that flat neighborhoods never see. Our Gate Access Control work starts with a written scope and a documented photo record, so you know exactly what was installed and how it was wired.
Keypad Entry
Signs you need it
A keypad that works in the morning but not in the afternoon heat, or one that eats codes one week and rejects them the next, is failing and will only get worse.
What it costs in Burbank
Keypad installations and replacements in Burbank typically run $300 to $700 installed, and full replacement of a dead board or keypad runs $325 to $750, depending on brand and wiring condition.
How we do it
We test the existing wiring for continuity and voltage drop, install the new keypad, program entry codes, and photograph the wiring terminations before closing the enclosure.
Video Intercom
Signs you need it
If you can hear a visitor but cannot see them, or the camera feed drops whenever the gate moves, the intercom cable or camera module is failing.
What it costs in Burbank
Operator arm replacements for Burbank gates run $450 to $1,050, and full gate opener replacements run $950 to $2,700, with labor at $95 to $140 per hour when a new arm is involved.
How we do it
We identify whether the fault is in the camera, the indoor monitor, or the cable run, replace the failed component, and photograph the new setup with the gate in both open and closed positions.
What Gate Access Control Costs in Burbank
| Item | Typical range in Burbank |
|---|---|
| Keypad installation or replacement | $300 - $700 installed |
| Dead board or keypad replacement | $325 - $750 installed |
| Operator arm replacement | $450 - $1,050 installed |
Can you install a phone entry system on a gate without an intercom?
Yes. Phone entry systems can be added to most existing gates, and in Burbank hillside homes the cellular-based units often work better than long wire runs. Call (213) 577-1120 for a written quote.
Why does my gate keypad fail every summer in Burbank?
Heat. Burbank routinely tops 100°F in summer, and keypads mounted in direct sun on black iron gates run hot enough to damage circuit boards. We can relocate the keypad or add a shaded enclosure to extend its life.
Gate Parts & Welding in Burbank
Gate parts and welding in Burbank is a structural discipline as much as a mechanical one. The 1940s and 1950s ranch homes in the Burbank flats often have gate posts set in concrete that has cracked and settled over the decades, so the parts that fail first are typically hinges, welds, and post bases rather than the gate operator itself. Hillside properties near the Verdugo foothills add twisted frames and sheared welds from gates that have been fighting gravity for years. Our Gate Parts & Welding work is documented the same way everything else is: photos of the failed part, the new part, and the finished weld before we leave.
Hinge Replacement
Signs you need it
A gate that drags on the latch side, scrapes the driveway, or has a visible gap opening at the top hinge is telling you the hinge has worn or the post has pulled.
What it costs in Burbank
Gate repair labor in Burbank runs $95 to $140 per hour, and a full operator replacement with a new arm runs $950 to $2,700, depending on brand and post condition.
How we do it
We remove the old hinge, check the post for sound steel and the footing for movement, set the new hinge with the gate level, and photograph the finished alignment from both sides.
Gate Rollers
Signs you need it
A sliding gate that jumps track, grinds when it moves, or sits lower on one end has a failing bottom roller or a bent track, and running it in that state wears out the operator faster.
What it costs in Burbank
Replacing bent track sections or welding broken gate frames in Burbank typically falls between $300 and $800, with the roller and track work priced on a written quote before any work starts.
How we do it
We lift the gate off its track, inspect both bottom rollers and the rail for wear, replace the failed parts, re-seat the gate, and photograph the roller positions before and after.
What Gate Parts & Welding Costs in Burbank
| Item | Typical range in Burbank |
|---|---|
| Gate repair labor | $95 - $140 per hour |
| Full operator replacement with new arm | $950 - $2,700 installed |
| Track section or welded frame repair | $300 - $800 |
Can you weld a broken iron gate on site in Burbank?
Yes, in most cases. We carry portable welding equipment and can repair cracked pickets, broken frame joints, and snapped hinge plates on site. A written price is prepared before the weld begins.
Why does my sliding gate keep falling off its track in Burbank?
Santa Ana winds in fall and winter are brutal at this valley mouth, and they regularly knock sliding gates off bottom rollers. Worn rollers magnify the problem, so we check them on every wind-related call.
Brands We Service in Burbank
Our technicians work on FAAC, BFT, Linear, and Viking automation, among others, and we stock common parts for these brands locally so repair work in Burbank does not stall waiting on a shipment. See our brands for the full list.
Pricing for Gate Repair in Burbank, CA
| Service | Typical range in Burbank |
|---|---|
| Gate repair labor | $95 - $140 per hour |
| Full operator replacement with new arm | $950 - $2,700 installed |
| Track section or welded frame repair | $300 - $800 |
| Keypad installation or replacement | $300 - $700 installed |
| Dead board or keypad replacement | $325 - $750 installed |
| Operator arm replacement | $450 - $1,050 installed |
Burbank’s extreme heat pushes component failures earlier than in cooler parts of Los Angeles, and hillside installs with slope-related strain can add structural work to a simple parts job. Every price above is written down and handed to you before any work starts, under Clause 1 of the Haven Standard.
Neighborhoods We Serve in Burbank
We cover the entire city of Burbank, and our typical response time for gate repair calls is a live answer at any hour with a technician dispatched the same day when the situation calls for it.
- Burbank Hills
- Media District
- Magnolia Park
- Rancho Equestrian
- Verdugo foothills
Service Area - Cities Near Burbank
We work throughout Burbank and the surrounding valley cities. If you are in North Hollywood, CA, Sun Valley, CA, Tujunga, CA, or Studio City, CA, the same written-price standard applies.
Serving Burbank, CA - Our Local Coverage Area
We’re based in the Burbank area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Burbank
Most gate repairs do not require a permit, but new gate installations and significant structural changes in Burbank may need city approval depending on setback, height, and whether the gate is on a hillside. We can tell you what applies to your property during the estimate.
Yes. We service commercial and studio-adjacent gates in the Media District and near the Warner Bros. and Disney campuses, and we can work with vendor credentialing requirements. Access control on high-cycle gates is a routine job for us, not a special case.
A live person answers at (213) 577-1120 around the clock, and for emergency repairs in Burbank we dispatch a technician as soon as one is available. Written pricing still applies before any work starts.
Call (213) 577-1120 for a free estimate on any gate repair, access control, or parts and welding job in Burbank. A written price is delivered before any work begins, and every visit ends with a documented photo record of what was found, what was changed, and how it was left.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Burbank Customers Say
"Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B."Our gate was hit by a delivery truck. They came out, documented the damage properly for the insurer, and the claim went through without an argument."
- Camille R."They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."
- Nadine C.