Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Encino
Gate installation in Encino usually runs $4,800-$14,600 for a full automated driveway gate with operator, depending on whether it’s a swing or slide configuration and whether the existing conduit can be reused. Most homes here need the work done on gates that were installed 20-35 years ago, so what looks like a simple swap often turns into new conduit, new footings, or a heavier operator than the original pilasters were built for. We’ve done enough installs south of Ventura Boulevard and up through Encino Hills to know which questions to ask before we quote. Call (213) 577-1120 and we’ll send a technician who can look at your specific gate, your specific wall, and your specific electrical run.
Why Vance Gate Repair Burbank Is Encino’s Preferred Gate Installation Company
Encino homeowners call us because we document what we find. That sounds simple, but it changes how an install goes. Before we touch anything, you get a written scope, a written price, and a photographed record of the existing condition. After we finish, you get a photo log of what was set, what was pulled, what was torqued, and what was installed. That’s the Haven Standard, and it applies to every gate we build or hang in Encino, from a 14-foot ornamental slide gate on a corner lot near Louise Avenue to a pedestrian gate off a pool deck in the flats.
Adrian Vance started this company in 2014 after years of commercial access-control work, and he carried the documentation habit with him. That’s why our Gate Installation team hands you a written record with part numbers, limit-switch settings, and conduit sizes before we leave. No future technician has to guess what’s in the ground. You shouldn’t have to pay twice to rediscover what a previous contractor already figured out.
We also answer the phone. A live person, 24 hours a day, seven days a week. If your gate fails open at midnight on a Saturday, you’re not leaving a voicemail and hoping. You’re talking to someone who can dispatch a background-checked, uniformed technician to Encino with your name and photo sent before arrival.
For gate installation in Encino specifically, the review pattern we see is trust built on transparency: written prices before work starts, free second opinions on competitor estimates, and the 365-Day Done Right Promise. If the install isn’t right, we make it right within a full year, no argument, no fee. We’ve repaired and installed over 22,000 gates since 2014, and every one had a written price before the first tool came off the truck.
Our Gate Installation Services in Encino
Driveway Gate Installation
Encino’s housing stock is split between 1950s-1970s ranch homes on generous flat lots and large custom estates built in the 1980s-2000s. Both present different driveway gate challenges. The ranches were never engineered for the weight and torque of modern operators, so we routinely pour new footings and reinforce pilasters before hanging a gate. The estates usually have gates that are just old: the automation is obsolete, but the steel or ornamental iron panel itself might be worth reusing. A new driveway gate install on a flat Encino lot, with a single operator and standard steel or aluminum panel, typically runs $5,200-$9,800. Custom ornamental iron or wood-clad gates run higher.
Pedestrian Gate Installation
Pedestrian gates in Encino run the same gauntlet as driveway gates, just on a smaller scale. Summer heat breaks down the closer springs and latch hardware, and UV exposure ruins powder coat faster than people expect. A pedestrian gate install, including a magnetic lock or electric strike and a keypad or intercom, typically runs $1,800-$4,200 in Encino depending on the width, material, and whether we need to core into a stucco wall for the lock. The truth is most older pedestrian gates weren’t built with automation in mind, so the latch zone needs reinforcement before anything electric goes in.
Sliding Gate Installation
Sliding gates are common on Encino’s larger properties, especially where a driveway slopes or where a swing gate would eat too much space. But they take a beating from the Valley’s heat. Thermal expansion on steel slide gates in sustained 105°F+ weather causes binding, warping, and stripped rack and pinion teeth. We see it every August. A new sliding gate install in Encino, with a track or cantilever design, operator, and safety photo-eyes, typically runs $6,800-$14,600. The higher end reflects heavier duty hardware, longer panels, and the structural work needed when the existing track bed was never properly reinforced.
Swing Gate Installation
Swing gates remain the most common new install across Encino, particularly on the walled properties between Ventura Boulevard and the Encino Hills ridgeline. The issue here is rarely the gate panel itself-it’s the hinge posts. Older posts are often set in shallow footings, and years of torque from heavy ornamental gates have loosened them. We open the wall, set new steel posts in deep concrete, and only then hang the gate. A dual swing gate install in Encino, with a paired operator system and full safety edges, typically runs $7,500-$13,800. Single swing gates run $4,800-$9,200.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterTrusted Brands We Service in Encino
We work on nine major gate-automation brands, so we don’t steer you toward replacing a motor just because we don’t stock parts for the one you have. For Encino customers, we keep common parts for Linear, Viking, DoorKing, and Ghost Controls operators on our trucks. That means faster diagnosis and fewer return trips. If you already have a Viking swing operator and the board is fine but the limit switch is gone, we replace the limit switch. We don’t upsell you a full system. That said, when you do need a new operator, we specify the right brand and model for your gate weight, cycle frequency, and exposure to Encino’s summer heat.
Common Gate Installation Problems We See in Encino Homes
- Undersized conduit from the late 1980s and early 1990s. The original low-voltage and line-voltage runs serving many of Encino’s security gates from that era were never sized for modern operators. Current City of Los Angeles electrical code requires larger conduit, so what starts as a motor swap becomes a full operator replacement plus conduit rework before the city will sign off.
- Thermal expansion on steel slide gates. Sustained triple-digit Valley heat causes the steel to expand enough to bind against the track or strip the rack teeth. We address this with proper clearance settings, thermal expansion joints in the track, and heavier-duty rack hardware.
- UV-degraded powder coat on aluminum swing gates. Years of Encino sun break down the finish, which exposes the aluminum to corrosion around hinge posts. That corrosion eats the post caps, loosens the hinges, and lets the gate sag at the corner. By the time most homeowners notice, the hinge post needs replacement, not just refinishing.
- Shallow footings and failing posts. Older ranch homes south of Ventura Boulevard often have gate pilasters set in minimal concrete, never designed for a heavy automated gate. On an install, we cut out the old post, pour a proper footing, and set a new steel post that can carry the load. If you skip this step, the new gate will sag within years.
Pricing for Gate Installation in Encino, CA
Here are the price ranges for gate installation work in Encino, based on what we’ve actually quoted and installed in this specific market:
- Single swing gate with operator: $4,800-$9,200
- Dual swing gate with paired operators: $7,500-$13,800
- Sliding gate with track or cantilever and operator: $6,800-$14,600
- Pedestrian gate with electric lock and keypad/intercom: $1,800-$4,200
- Conduit rework for code compliance (per foot, trench and pull): $18-$45
- New post footing and steel post (per post): $900-$2,400
Every one of those numbers is written down and agreed to before any work starts. That’s Haven Standard Clause 1: the written price is handed over before tools come off the truck. The final invoice is the written price, not a surprise. If we find something during the install that changes the scope, we stop, show you what we found, and write a new price for approval before continuing. You never come home to a surprise bill. Call (213) 577-1120 for a free estimate on your specific gate.
We Also Serve Cities Near Encino
Our crews run installs through Tarzana, Reseda, Sherman Oaks, and Van Nuys on the same schedule as Encino. If you’re a mile into Tarzana or just over the 405 in Sherman Oaks, the drive doesn’t change our pricing or our response. You get the same written scope, the same photo documentation, and the same 365-Day Done Right Promise. We coordinate dispatch from the Los Angeles office, and our technicians work locally throughout the San Fernando Valley.
Serving Encino, CA - Our Local Coverage Area
We’re based in the Encino area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Encino
If your early-1990s gate operator still runs but the original line-voltage conduit is undersized by current City of Los Angeles code, the retrofit almost always costs more than a full operator replacement once conduit rework is factored in. Your technician can check the conduit size, the board condition, and the motor brushes in about a half hour. Most operators from that era in Encino are at the point where parts are discontinued, the board is heat-fatigued, and the conduit has to come out anyway. In that case, replacing the operator and pulling new conduit in one visit is the cheaper, cleaner answer. Call (213) 577-1120 and we’ll put a named technician on your gate with a written diagnosis.
Because sustained 105°F+ heat causes the steel to expand enough to bind against the track or strip the rack teeth. It’s not a misaligned photo-eye, it’s thermal expansion. The fix is not just resetting the gate on the track; it’s setting proper clearance tolerances for the gate’s full thermal range, which in Encino means planning for 110°F in August and 40°F in January. We also check whether the rack is pinned at the correct spacing so the teeth don’t climb under thermal load. A gate that binds in summer will keep binding until the clearance is set correctly.
Yes. Current City of Los Angeles code requires automatic gates to have entrapment protection: photo-eyes on the gate path and edge sensors on the leading edges where the gate could contact a person or vehicle. Many Encino gates installed before the late 1990s were hung without either. If we’re doing an install on a property with an older gate, we bring the entire system up to current code: photo-eyes, safety edges, and a warning placard. That’s part of the install price, not an add-on. A gate without modern entrapment protection is a liability, full stop.
Because the original conduit runs from the late-1980s and early-1990s security-upgrade wave were frequently undersized by today’s City of Los Angeles electrical code. The wire inside that older conduit is often too light for modern operators’ current draw, and the conduit itself may be too small to pull upgraded wire. When we pull new conduit, we also eliminate failed splices, abandoned direct-burial runs that were never to code, and damage from decades of soil movement in the Valley’s clay. You don’t pay for conduit rework just because the code says so; you pay because if we don’t do it, the new operator will trip breakers, cook control boards, and fail early.
Usually not. The panel itself is rarely what causes a sagging swing gate in Encino. The problem is the hinge post. Years of torque from a heavy ornamental gate loosen a post that was set in a shallow footing, and the post leans, which makes the gate sag. The panel may also be bowed from UV exposure and heat, but the hinge post is the root cause most of the time. The fix is to remove the old post, pour a deeper footing, set a new steel post, and only then rehang the gate. If we rehang the gate on a leaning post, you’ll be calling us again in two years.
On a ranch property south of Ventura Boulevard in Encino, our tech found a 1992 DoorKing slide gate operator whose control board had fried from the Valley heat, and the original line-voltage conduit was undersized for a modern LiftMaster replacement. We pulled new conduit, set the post footing for the gate operator, and added a loop detector and safety photocell to meet current code before rehanging the gate. That’s the job: name what you found, name what it costs, name what you left behind.
Call Vance Gate Repair for Your Encino Gate Installation
If you need a gate installed on your property in Encino, call (213) 577-1120. You’ll get a live person, a free estimate, and a written price before any work starts. We’ll schedule a technician who knows Encino’s housing stock, its heat, and its older gate infrastructure. And when we leave, you’ll have a documented record of everything we did: part numbers, limit settings, conduit sizes, and photos. That’s the Haven Standard, on every single job. No surprises, just documented work.
Written by Adrian Vance, Owner at Vance Gate Repair Burbank, serving Encino since 2014.
Gate Installation in Nearby Areas
