Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterLinear Gate Motor & Opener in Burbank: What to Know First
We repair and install Linear gate motors and openers in Burbank as an independent Linear service provider, not a manufacturer affiliate. Most Linear swing-arm or slide-motor failures we see get diagnosed the same day and repaired within 48 hours once parts are on the truck. Pricing is written down before any work starts: a standard Linear control board replacement in Burbank usually lands between $280 and $520 including labor; a full swing-arm motor rebuild runs $450 to $950 depending on model and arm condition.
If you own a Linear gate that will not open, opens halfway, or hums without moving, this page tells you what is actually wrong, what it costs, and how we leave the job. Call (213) 577-1120 and a live person answers, any hour.
How Linear Products Fail - and How We Fix Them
- Linear LRA swing-arm: the arm detaches or sags under load. The LRA series uses a zinc hub coupling that strips after a few years of the gate being manually pushed against motor resistance. We see it most in Burbank’s Magnolia Park and Chandler Bike Path homes where gates get heavy daily cycling from dog walkers and delivery traffic. Our fix: replace the hub with an aftermarket steel coupling and re-set the arm geometry, not just tighten the old fitting.
- Linear PRO Series (formerly ProAccess): receiver drift. The PRO line’s built-in radio receiver can lose its learned code after a power flicker, which Burbank Water and Power reports frequently during Santa Ana wind season. The symptom is a transmittal that worked yesterday doing nothing today. We re-learn the receiver and, if it recurs, install a surge protector inline with the 24V transformer.
- Linear APeX control board: limit switch fault loops. APeX boards log a “limit fault” when the thermal overload in the motor trips. Homeowners assume the board is dead. It usually is not. We test the motor’s amp draw first; a tired capacitor or a gate dragging on a settling concrete post is the root cause about two-thirds of the time in older Burbank neighborhoods like Providencia Park.
- Linear slide-motor (SLR line) gear wear at the drive sprocket. The SLR slide motor uses a brass final-drive gear that wears smooth after roughly four to six years of daily opening on a fifteen-foot gate. The gate starts to hesitate, then screech, then stop mid-travel. Replacing the gear set is a $200 to $400 repair, far below a full motor swap, and we photograph the worn gear next to the new one before reinstalling the cover.
- Battery backup on newer Linear units: extended outage behavior. Burbank homes in the hills above Sunset Canyon lose power during high wind. Linear units with the optional battery backup are designed to cycle a few times, not all weekend. If the gate runs flat, the control board may not resume AC operation without a manual reset. We add a small inline relay on installations where the homeowner wants manual-open capability after battery depletion.
Our Linear Gate Motor & Opener Process
- 1
Call and describe the symptom. We ask what the gate is doing, not what you think is broken. “Humming but not moving” and “dead silent” are two different failure branches.
- 2
Dispatch with Linear parts on the truck. Our Burbank van carries LRA arm assemblies, PRO receiver modules, APeX control boards, SLR gear sets, and the common capacitors for all of them. No second appointment for parts on typical failures.
- 3
Onsite diagnosis with measurements, not guesses. We check amp draw, limit switch position, capacitor microfarads, and ground continuity. The number goes on the work order.
- 4
Written price before any tool is picked up. The flat price is handed to you on paper. That is Clause 1 of our Haven Standard. It does not change at the end of the job.
- 5
Repair or replace using OEM or better aftermarket parts, stated plainly. If the original Linear part failed prematurely, we will tell you and recommend the part we have seen last longer. We never hide that decision from you.
- 6
Test the full cycle, then leave the record. We run the gate through eight full open-close cycles, photograph the new part installed, the board LEDs, and the final limit positions. The photo log is yours before we pull out of the driveway, and it goes into our job file under your address.
BeforeAfterWhat Linear Gate Motor & Opener Costs in Burbank
| Service | Typical Burbank Range | Notes |
|---|---|---|
| Linear control board replacement | $280 - $520 | Includes labor, board, and surge re-check |
| Swing-arm motor rebuild (LRA) | $450 - $950 | Depends on arm assembly condition and hub type |
| SLR slide motor gear set replacement | $200 - $400 | Far cheaper than a full slide motor |
| Receiver module replacement (PRO line) | $150 - $320 | Includes re-learn and remote testing |
| Full Linear swing operator replacement | $1,100 - $2,400 | Written quote after measure; includes arm, mounts, and adjustment |
What moves the number: whether the existing arm bracket is still square on the post, whether the run from the panel to the motor carries proper gauge wire, and whether we are reusing or replacing photo-eyes. The estimate is written, free, and quoted before work starts, under Clause 1. Call (213) 577-1120 and we will give you a number on the phone for most jobs.
Why Burbank Homeowners Call Vance Gate Repair Burbank for Linear Work
We carry Linear parts on the truck. We know that a Magnolia Park gate on a 1950s concrete post has a different failure signature than a gate on a newer stucco column in the Hillside District. And we do not talk you out of a repair when a $90 gear set beats a $1,800 slide-motor replacement.
Vance Gate Repair Burbank has repaired and installed more than 22,000 gates since 2014, and every one of them included a written price before work started and a photographic record before the technician left. That is Adrian Vance’s standing rule, carried over from commercial access-control documentation. If the repair is not right within 365 days, we make it right at no charge. It is in writing.
We service Linear every week, but we also work on LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so you are not locked into one brand path when a motor is beyond saving and a different operator is the more honest recommendation.
FAQs
No. As an independent repair company, we do not report repairs to Linear’s manufacturer warranty system, and most Linear residential warranties have already expired by the time the gate fails. If your unit is still under manufacturer warranty and you want a factory-authorized repair, we will tell you that plainly before any work begins. What we will not do is tell you a repair is necessary when a $30 capacitor is the actual fault.
Same-day dispatch is typical for a dead gate in Burbank, with most repairs completed within 48 hours because our van carries the LRA, SLR, PRO, and APeX parts we see most. A live person answers at (213) 577-1120 at any hour, and we will tell you the earliest available dispatch in the first thirty seconds of the call. No callback queue, no booking later.
We use both, and we tell you which one goes in. Genuine Linear parts are specified when the gate is newer or when a particular board revision is required. We recommend aftermarket parts when a specific Linear component, like the LRA hub coupling, is a known weak point that fails the same way twice. Every part number is written on the work order and photographed before the cover goes back on.
Repair it if the failure is a single component: a control board, a gear set, a receiver module, a capacitor. We will tell you the cost of the repair, the typical remaining life of the other major components, and the cost of a full replacement, in writing. If the motor windings are burned or the operator housing is cracked from gate sag, we will recommend replacement and show you the evidence we used to reach that conclusion. We never steer a Burbank homeowner into a $2,500 replacement when a $300 repair fixes the gate for years. Name what you found. Name what it costs. Name what you left behind.
Yes. Most Linear PRO units accept a dry-contact opening input, which means we can wire a DoorKing or Aiphone intercom or a GSM cell-dialer into the existing board without replacing the operator. The integration cost depends on whether the wire run from the house to the motor is accessible and what voltage the intercom supplies.
Written by Adrian Vance, Owner, Vance Gate Repair Burbank at Vance Gate Repair Burbank, serving Burbank and nearby areas.