Ghost Controls Hinge & Roller Replacement Nationwide

Ghost Controls Hinge & Roller Replacement: The Burbank Owner’s Guide

We stock Ghost Controls-compatible hinge and roller replacement parts on our trucks, and most Burbank jobs are completed same-day at an installed price between $95 and $230 per hinge or roller assembly, depending on your gate’s weight and which generation of hardware you have. The way owners usually find us is the same story: the gate starts dragging on the ground, or it makes a grinding sound at the top of travel, or one morning it simply won’t swing because a roller finally gave out. Hinge and roller failures are the most common Ghost Controls mechanical issue we see in Burbank, ahead of motor problems, because these parts take the full weight of the gate every single cycle.

Call (213) 577-1120

Our technicians carry a spread of Ghost Controls hinge sizes, roller brackets, and wheel diameters on the truck, so a diagnosis and repair usually happens in one trip. You get the written price before we touch a tool, and every adjustment and replacement is photographed before we leave. That’s the Haven Standard: you see what we found, what it cost, and what we installed.

Which Ghost Controls Models This Applies To

Ghost Controls makes gate openers designed for a range of swing gate sizes, and the hinge/roller assemblies differ by gate weight class and whether you have a tube-steel or ornamental iron gate. Most residential Ghost Controls setups in Burbank use either the standard-duty hinge set rated for gates up to roughly 600 pounds or the heavy-duty version intended for longer, wind-loaded gates up to about 900 pounds. The easiest identification method is the wheel diameter: standard-duty rollers typically measure 2 inches, while heavy-duty rollers are often 2.5 to 3 inches and use a larger axle pin.

Compatibility gets tricky with the roller bracket spacing. Ghost Controls has changed bracket hole patterns between production generations, so an older gate (2015-2019) often won’t accept a current-production roller without drilling a new hole pattern. We check the bolt spacing and wheel offset before we quote, because a mismatched roller causes the gate to sit low or scrape the post. For most Burbank residential gates, a quality aftermarket hinge and roller set matched to the original dimensions performs as well as Ghost Controls OEM parts. For heavier ornamental gates, we recommend OEM or equivalent-grade hardware, because the cast metal in cheaper aftermarket rollers tends to crack at the weld joint in our summer heat. One more note: Vance Gate Repair Burbank is an independent service provider, not affiliated with Ghost Controls, and we also stock parts for LiftMaster, Mighty Mule, and DoorKing gates.

Signs Your Ghost Controls Hinge & Roller Replacement Is Failing

• Gate drags or scrapes the ground at the far end of travel. A worn roller wheel loses diameter, so the gate sags slightly and the latch-side bottom edge catches pavement or gravel when it opens or closes.
• Grinding or squealing during movement. The roller wheel’s internal bearing dries out and binds, or the axle pin wears an oval into the bracket, producing metal-on-metal noise that worsens over time.
• Gate wobbles or rocks when you push it by hand. A worn hinge pin or egged-out hinge barrel lets the gate move on its mounts, causing visible lateral play at the latch end.
• Gate sits visibly lower on one side. This is often a collapsed or bent hinge on the motor side, especially on wide single-leaf gates where the opener arm exerts constant torque.
• Opener motor working harder than usual, or stopping mid-cycle. When hinges and rollers bind, the Ghost Controls opener draws more current. Some owners notice the motor gets warm, or the gate stops partway and reverses.

If any of these symptoms appear, address them before the opener’s overload protection becomes a permanent condition. Replacing hinges and rollers is far less expensive than replacing a burned-out motor.

Before

After

Replacement Cost & What’s Included

In Burbank, hinge and roller replacement for a Ghost Controls gate typically runs from $95 to $230 installed per hinge or roller assembly, with most single-gate repairs requiring two or three parts and landing between $190 and $520 total. The main cost drivers are gate weight class (standard versus heavy-duty hardware), whether the bracket bolt pattern requires fabrication to match an older gate, and whether the gate needs re-leveling after the new parts go in.

Our pricing is flat and written: the quote you sign before we start is the price you pay, parts and labor included, no surprise line items at the end. Every hinge and roller replacement is covered under the 365-Day Done Right Promise, which means if it isn’t right within a year, we fix it with no additional charge. Before we leave, you receive a photographed record of the parts replaced, the measurements we took, and the final level and tension reading on the gate.

DIY or Call Us?

An owner can safely check the obvious: wheel diameter, bracket hole spacing, and visible cracks at the hinge weld or roller axle. That information helps us bring the right parts on the first visit. Replacing hinges and rollers, however, means supporting the full weight of the gate while parts come off, and a lot can go wrong in those minutes. A gate shifted off its level by even half an inch will bind against the opener, strip gears, or yank fasteners out of a wooden post. We’ve seen more than one Burbank homeowner put a gate on a jack stand, remove the wrong bolt, and end up with a gate in the driveway and a bent hinge pin.

We’ll also check the opener’s force settings after the new hardware is in, because a new roller changes the friction profile and an opener set too high can push the gate past its intended stop. That’s a set of measurements most DIY repairs skip, and it’s where we catch problems before they become service calls. If you’re not certain what you’re looking at, call (213) 577-1120 and we’ll talk you through what to photograph.

FAQs