Ghost Controls Gate Parts & Welding Nationwide

Ghost Controls Gate Parts & Welding in Burbank: What to Know First

We provide independent Ghost Controls gate parts and welding in Burbank, with most hinge replacements, gate roller swaps, and latch repairs completed the same day the parts are in hand. A typical Ghost Controls parts-and-welding job in Burbank runs between $185 and $650, depending on whether we’re welding, replacing hardware, or both. The price is written down and handed to you before any work starts, under Haven Standard Clause 1. If you own a Ghost Controls opener and the gate itself is sagging, binding, or hanging off its hinges, call (213) 577-1120 and we’ll tell you what we charge for the common fixes before we even schedule the visit.

Call (213) 577-1120

This page is for Burbank homeowners running Ghost Controls operators who need the steel, the hinges, the rollers, or the latch work done right. As an independent Ghost Controls service provider, we’re not affiliated with the manufacturer, but we work on their equipment constantly, and we document every repair with photos and written notes so you can see exactly what was done.

How Ghost Controls Products Fail - and How We Fix Them

Ghost Controls makes capable openers, but the failure modes we see on Burbank gates usually aren’t in the motor. They’re in the metal around it.

• Hinge sag on the R-series single-arm openers. The Ghost Controls R30 and R20 single-arm kits are popular on lightweight tube-steel gates in Burbank, but the top hinge takes a beating when the arm pushes. We regularly find the top hinge stretched 3 to 5 degrees past plumb, which makes the gate scrape the grade and eventually faults the opener’s obstruction sensor. Our fix: cut the stretched hinge off, weld a new barrel hinge in place, and set the gate so the operator isn’t fighting gravity.
• Gate roller failure on slide installations. Ghost Controls LSM and SLD slide gate operators are often paired with cantilever or track gates in Burbank’s tighter side yards. The nylon rollers wear flat on one side within two to three years, especially with the dry Santa Ana dust season. We replace the roller set and check the track level with a machinist’s level, not just a bubble stick; a 1/8-inch dip over an eight-foot run is enough to make the operator work harder than it should.
• Receiver board burnout from repeated obstruction faults. On Burbank hillside homes, a gate that hits uneven concrete or a raised tree root will stall repeatedly. The Ghost Controls receiver board interprets repeated stall events as overloads and eventually lets go. We don’t just swap the board; we deal with whatever the gate was hitting. Welding a steel ramp plate or grinding the high spot is usually one-third the cost of throwing another board at the problem.
• Weld cracking at the pedestal to gate connection. The XP series kits put more force into the gate leaf than the lighter R-series, and the factory gate often wasn’t built to handle it. We see hairline cracks radiating from the welds where the pedestal meets the gate stile, especially on gates over 10 feet wide. Our welding repair means grinding the crack out, welding it hot with proper penetration, and adding a gusset plate so it doesn’t crack again the same way.
• Latch misalignment after any hinge work. Ghost Controls gates often run a solenoid-driven latch, and when the gate shifts a quarter inch, the latch jaw won’t seat. We align the latch to the new gate position and replace worn latch pins with stainless steel so you’re not doing this twice a year.

One Burbank-specific note: the dry heat in summer cooks the lubricant out of gate hinges faster than any coastal city nearby. We’ve seen hinge pins in Magnolia Park seize solid after three months of untreated August exposure. We use a high-temperature graphite-based grease on Ghost Controls gates here, not standard lithium, because it doesn’t dry up in a Burbank July.

Our Ghost Controls Gate Parts & Welding Process

Every Ghost Controls gate parts and welding job we run in Burbank follows the same sequence. It keeps the work honest and keeps you from paying for someone’s guess.

1. 1
   You call, we talk through the symptom. A live person answers at (213) 577-1120, any hour. We listen, ask for photos if you have them, and then give you a written price range before we dispatch. That’s Haven Standard Clause 1 in practice.
2. 2
   We inspect the gate, not just the operator. Our technician checks hinge wear, roller condition, track level, welding integrity, and the gate’s relationship to the Ghost Controls operator. We measure, photograph, and write down the numbers.
3. 3
   Parts decision: OEM or quality aftermarket. For Ghost Controls electronics, we recommend OEM parts, warranty-safe. For steel hardware like hinges, rollers, and brackets, we often spec domestic fabrication or heavy-duty aftermarket parts because they outperform the original lightweight steel. We explain the difference and show you the price before ordering.
4. 4
   We do the welding and hardware work. All welding on Ghost Controls gates in Burbank is done by our technicians using MIG or stick, depending on material thickness, with tack-free root welds and full penetration. The work area is prepped but never left unguarded.
5. 5
   We test against the Ghost Controls operator. We run the gate through several open-close cycles, check the limit settings, and confirm the operator isn’t faulting. If the operator needs a setting adjustment, we photograph the change.
6. 6
   You get the photo log and written record. Before our technician leaves, you receive a documented record of what was found, what was replaced, and the part numbers. That’s Haven Standard Clause 4, evidence on every job.

Name what you found. Name what it costs. Name what you left behind. That’s the Vance Gate Repair Burbank way, and it applies to every Ghost Controls job we do.

Before

After

What Ghost Controls Gate Parts & Welding Costs in Burbank

Here’s what our Burbank customers typically pay for Ghost Controls gate parts and welding work. These are real ranges, not placeholders. You’ll get a written quote before we touch the gate.

• Gate hinge replacement (single leaf): $185 to $320, including the welded-in hinge barrel and alignment test.
• Gate roller replacement (slide gate, set of 4): $220 to $410, depending on roller size and whether the track needs grinding.
• Weld repair at a cracked pedestal or hinge: $150 to $380, depending on crack spread and whether gusset plates are required.
• Latch and lock replacement or realignment: $130 to $260, including the striker plate adjustment.
• Full hinge and hardware replacement (double gate): $540 to $920, including four new barrel hinges, latch realignment, and a complete operator test pass.

What moves the price: gate weight and leaf width, access room for the welder, whether the existing steel is thick enough to weld safely, and whether the Ghost Controls operator needs a limit reset after the hardware work. We don’t surprise you at the end. The written price covers the labor, the parts, and the test pass. Every Ghost Controls parts estimate in Burbank is free, and the second opinion on another company’s written estimate is also free.

Why Burbank Homeowners Call Vance Gate Repair Burbank for Ghost Controls Work

We service nine gate automation brands, including Ghost Controls, LiftMaster, Mighty Mule, and DoorKing, so when you call us for Ghost Controls gate parts and welding in Burbank, you’re getting technicians who understand how different operators interact with different gate steel. We’re not steering you toward a replacement motor; we’re fixing the gate that’s already on the property.

The 365-Day Done Right Promise backs every Ghost Controls repair we complete. If our welding or hinge work isn’t right within a year, we make it right, no argument, no fee. That’s the whole promise. Adrian Vance built this company on access-control documentation, and he still personally reviews job photos weekly. The technicians who arrive at your Burbank home are background-checked, uniformed, and dispatched with their name and photo sent to you before arrival.

We answer the phone live, 24 hours a day, seven days a week. When your gate is hanging off its top hinge at 9:40 PM in Burbank, you don’t need a voicemail loop. You need someone who can tell you whether it’s safe to leave the gate open or closed until morning, and what the repair will cost.

FAQs