Automatic Gate Repair in Burbank, CA

Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Styles & brands we work with

‹

›

Before & after – our own jobs

‹

BeforeAfter

BeforeAfter

BeforeAfter

›

Automatic Gate Repair in Burbank, CA

If your automatic gate in Burbank has stopped responding to your remote, is making a grinding noise, or won’t close fully, you typically need a technician to diagnose the motor, logic board, or safety sensors. Most Gate Repair services in Burbank, CA, range between $180 and $450, depending on whether the issue stems from a simple sensor misalignment or a failed circuit board. We provide upfront, written pricing before any work begins, ensuring you know exactly what the repair entails before we pick up a tool. You can reach us at (213) 577-1120 anytime to discuss your specific gate automation issues.

When an automatic gate fails, it is often more than just a convenience issue; it is a security risk for your Burbank property. Whether you are dealing with a faulty Viking swing-gate operator in the hills or a struggling Linear slide-gate motor on a flat lot, our approach remains consistent with the Haven Standard. We provide a documented record of every visit, including the specific settings we adjusted and the parts we installed. This ensures that you aren’t paying twice for the same problem and that any future technician has a clear history of your gate’s maintenance. If you are experiencing issues with your system, our Gate Repair in Burbank team is ready to help.

When You Need Automatic Gate Repair

Electric Gate Repair involves complex assemblies of electrical, mechanical, and safety components. Over time, the environment in Burbank-from the heat cycles that affect motor capacitors to the dust that settles on optical sensors-can cause specific failures. We frequently see these symptoms in our local service calls:

• The gate reverses unexpectedly: Often caused by a misaligned photo-eye (the infrared beam that stops the gate if something crosses the path). If the beam is blocked by debris or the lenses are off-center by even an inch, the motor assumes an obstruction exists and reverses the gate for safety.
• Grinding or scraping noises: This usually indicates worn gears or a drive chain that has lost tension. In many older installations, we find that the grease has dried out, causing metal-on-metal friction that will eventually strip the gears if not addressed.
• The gate won’t open or close at all: If you hear a click but the motor doesn’t hum, the issue is often a failed start capacitor or a blown fuse on the control board. If the motor hums but the gate doesn’t move, the release mechanism may have been left in manual mode or the drive gear has sheared.
• Inconsistent remote operation: If the gate only responds when you are inches away, the antenna or the receiver board is likely failing. We check the signal strength and the wiring connections between the receiver and the main board to isolate whether the problem is the remote transmitter or the gate’s reception system.
• Gate drifts open or closed: This is common with hydraulic systems like those from FAAC or BFT. If the gate doesn’t stay in the position where it stops, the internal seals may be leaking, preventing the hydraulic pressure from holding the gate against the wind or gravity.

Our Automatic Gate Repair Process

We operate under the Haven Standard, which means we do not guess at problems or offer vague verbal estimates. When we arrive at your Burbank property, we follow a strict documentation process to ensure you are informed throughout the repair.

1. Visual Inspection and Testing: We start by testing the gate’s operation, listening for mechanical stress, and observing the motor’s behavior during a full cycle. We verify if the issue is electrical, mechanical, or a failure of the safety peripheral.
2. Written Scope and Price: Before we touch a tool, we present a written quote detailing exactly what we found and what it will cost to fix. Clause 1 of the Haven Standard ensures you have this price in writing, so there are no surprises when the invoice arrives.
3. Documented Evidence: Under Clause 4 of the Haven Standard, every visit includes a photo log of what was found, what was adjusted, and what was replaced. We take photos of the limit-switch settings, the wiring terminal, and the motor housing, providing you with a record of the work performed.
4. Repair and Calibration: We perform the necessary repairs, whether that involves replacing a control board, adjusting the tension on a drive chain, or realigning the safety sensors. We calibrate the motor settings to ensure the gate moves smoothly without unnecessary strain.
5. Verification: We run the gate through multiple cycles to ensure the problem is resolved. We then show you the photo record of the repair and confirm the gate is operating safely and reliably.

Before

After

Automatic Gate Repair Pricing in Burbank

We believe in transparency. Because we provide written pricing before work begins, you never have to worry about “surprise” fees. While every gate installation is unique, How Much Does Gate Repair Cost? (2026 Price Guide) - Burbank, CA depends on several factors, and the following table provides a general range for common automatic gate repairs in Burbank.

Please note that these are estimates. Factors such as the accessibility of the motor, the brand of the operator (such as BFT, FAAC, or Viking), and the condition of the existing wiring can impact the final cost. We offer free estimates on repairs, so call us at (213) 577-1120 to have a technician assess your specific situation.

FAQs - Automatic Gate Repair

How do I know if my automatic gate motor needs a repair or a full replacement?

Most gates can be repaired unless the motor housing is severely corroded, the internal gears are completely stripped, or the manufacturer no longer produces parts for that specific model. We specialize in diagnosing the specific component failure-such as a bad capacitor or a Gate Realignment issue-and provide a transparent assessment of whether a repair is the most cost-effective path. Call (213) 577-1120 for an honest evaluation of your current motor.

Can you fix my gate if it is a brand you don’t typically install?

Yes, we service nine major automation brands, including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Our technicians are trained to work on the motor already on your property rather than steering you toward a replacement. We focus on getting your existing system back in working order whenever possible.

What should I do if my gate is stuck open and blocking my driveway?

If your gate is stuck, first check if the manual release lever has been engaged; if so, you may be able to push the gate open or closed manually to clear your driveway. If the gate is stuck due to an electrical or mechanical failure, do not force the motor, as this can cause further damage to the gears or the arm bracket. Call (213) 577-1120 immediately, and we will prioritize your call to get the gate moving again.

Do you offer a warranty on your repairs?

We stand behind our work with our 365-Day Done Right Promise. If the specific repair we performed is not right, we make it right at no additional charge for one full year. We document every adjustment and part installation as part of our Haven Standard, so you have a clear, photographic record of what was covered.

If your automatic gate is acting up, don’t wait for a total failure. We provide clear, upfront pricing and documented records for every service call in Burbank. Whether it is a sensor issue or a complex motor failure, we have the experience to get it running smoothly. Call (213) 577-1120 today for a free estimate or to schedule a technician. We are ready to help you secure your property.

Written by Adrian Vance, Owner at Vance Gate Repair Burbank, serving Burbank.