Elite Welding & Fabrication Nationwide

Elite Welding & Fabrication: The Burbank Owner’s Guide

Elite gate parts needing welding or fabrication in Burbank typically run $180 to $520 installed, depending on whether we’re repairing a cracked hinge bracket, re-welding a broken gate frame joint, or fabricating a replacement mounting plate from scratch. We stock Elite-compatible weld plates, hinge tabs, and reinforcement gussets on the truck, and most repairs are completed same-day once steel is matched and the weld is dressed. The usual discovery is visual: a sagging gate leaf, a cracked weld bead at the hinge, or a bracket that’s pulled away from the post after years of Burbank heat cycles flexing the metal more than the original weld could take.

Call (213) 577-1120

Which Elite Models This Applies To

This covers the full Elite gate operator line we service: the SL-3000 and SL-3000UL swing gate operators, the Elite Slidegate series including the 7150 and 7220, and the older Elite Mighty Mule FM-series that shows up constantly on Burbank hillside properties. The parts that typically need welding or fabrication are not the operator internals themselves, they’re the steel around them: hinge brackets, gate frame tabs, operator mounting plates, and the occasional bent arm that connects motor travel to gate travel.

Identifying what you have is easier than owners expect. The operator housing has a model number on the underside of the cover or on the motor plate itself, and hinge brackets are matched by measuring bolt-hole spread and plate thickness, not by guesswork. Here’s the compatibility gotcha worth knowing: Elite operators made before 2012 used a thinner-gauge mounting plate that cracks at the weld toe where the arm bracket meets the gate frame. The current replacement brackets are 1/4-inch steel, and they need the gate frame reinforced behind them or the new bracket outlives the metal it’s bolted to. We stock OEM Elite plates and quality aftermarket equivalents cut to the same bolt pattern; for brackets where Elite only sells a full kit, a fabricated plate matched to the original dimensions is often the faster and cheaper fix.

Signs Your Elite Welding & Fabrication Is Failing

• Gate leaf sags visibly at the hinge side. The hinge bracket weld has cracked or the gate frame itself has fatigued. The operator keeps working, but it’s pushing a leaf that’s no longer square, which wears every downstream component faster.
• A sharp crack or pop when the gate starts or reverses. That’s a weld bead failing under load. Weld failures rarely announce themselves quietly once they start, and they don’t self-heal.
• Rust staining running down from a bracket or weld joint. Burbank’s dry heat hides this until winter rain. Rust lines mean moisture is entering a crack or seam, and the steel is oxidizing from the inside of the joint outward.
• The operator arm or mounting plate wobbles during travel. Bolts are loose or the plate they thread into has elongated its holes from repeated stress. Re-torquing alone usually doesn’t hold once the plate metal has deformed.
• The gate closes harder on one side than the other. A hinge or bracket that has shifted changes the swing geometry. The motor compensates until it can’t, and then you get a burned board or a bent arm added to the bill.

Before

After

Replacement Cost & What’s Included

Installed pricing in Burbank for Elite welding and fabrication breaks down by the scope of the repair. A straight hinge-bracket re-weld runs $180 to $260, including grinding back to clean steel, re-welding, and a rust-inhibiting prime coat. Reinforcing a cracked gate frame joint lands between $240 and $340 depending on how much gusset plate is needed. Custom fabrication, like a new operator mounting plate or a replacement arm bracket cut to match a non-standard gate frame, runs $320 to $520.

Every number is given in writing before any work starts. No hourly mystery billing, no “we’ll see when we open it up” line. You get the price for parts and labor broken out, you approve it, and we weld. The work carries our 365-Day Done Right Promise: if the weld fails or the bracket shifts within a year, we make it right at no additional charge. Under Haven Standard Clause 1, that written price is in your hand before a tool comes off the truck.

DIY or Call Us?

Here’s the honest split. An owner in Burbank can safely check for the obvious: a visible crack at the weld toe, a bracket that’s pulling away from the post (watch for daylight between plate and metal while someone else cycles the gate), or a sheared bolt head lying in the driveway. Those observations help you describe the problem accurately over the phone.

Where DIY goes wrong is the welding itself. Structural welds on a moving gate leaf carry dynamic load, not static weight, and a poorly penetrated weld on a hinge bracket holds right up until it doesn’t, usually with a several-hundred-pound gate leaf involved. Grinding the old weld without knowing the base metal thickness can remove material we’d need for a sound repair. If you’ve got welding gear and want to tackle it, we won’t lecture you, but for most Burbank homeowners the cost of our repair is less than the cost of a welding machine, a helmet, and the learning curve. Call (213) 577-1120 and we’ll give you a straight answer on what you’re looking at.

FAQs