Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Burbank
A gate repair in Burbank runs from a simple $175 hinge adjustment up to $3,800 for a full hillside slide-operator replacement, and most jobs we complete start to finish in a single visit. The real variable in this city isn’t the equipment, it’s whether the gate sits on a settled 1950s flat-lot footing or clings to a slope north of Kenneth Road. Our Gate Repair team has pulled operators off both, and the written quote you get before we touch a tool reflects exactly what we found under the cover. Call (213) 577-1120 and a live person answers, day or night.
Why Vance Gate Repair Burbank Is Burbank’s Preferred Gate Repair Company
Adrian Vance started this company in 2014 doing commercial access-control work, which means every Burbank job comes with the documentation habit most residential gate companies never developed. Before our technician leaves your driveway in the Burbank Hills or down in the flats off Magnolia, you get a photographed record of what was found, what was adjusted, and what was installed. No guessing later. No paying a second company to rediscover the same limit-switch setting.
We pull up to Burbank properties expecting two distinct problems. The ranch homes along the Verdugo foothills fight gravity, which means post footings settle and swing gates bind. The flat-lot bungalows built between the 1940s and 1970s typically have gates retrofitted decades after the home, often on unengineered concrete that cracks and shifts. Both patterns are familiar to us because we see them every week, not once a season.
Every repair we complete in Burbank carries a 365-Day Done Right Promise. If the work isn’t right within that year, we make it right. No argument, no fee, no expiration date inside the window. That applies to a hinge replacement in Rancho Adjacent and a full operator rebuild near the Disney campus alike.
Our Gate Repair Services in Burbank
Electric Gate Repair
Burbank’s mix of older residential swing gates and high-cycle studio perimeter gates means we diagnose more control-board and loop-detector failures here than in surrounding cities. A failed loop detector on a production-lot gate in the Media District can disrupt vehicle flow a dozen times a day. We test the loop, replace the detector where needed, and photograph the settings before we button the panel back up.
Automatic Gate Repair
Automatic gate repair in Burbank frequently comes down to heat. Operators sit inside metal housings that bake in San Fernando Valley sun, and rubber drive belts degrade faster here than in coastal zip codes. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so we fix the motor already on the property instead of steering you toward a replacement you may not need.
Hinge & Post Repair
Post-settling is the single most common structural failure we see on Burbank flat-lot retrofit gates. The original owner bolted a gate to an existing driveway approach without engineered footings, and fifty years of soil movement later the post leans a half-inch, the hinge binds, and the operator overloads every cycle. We re-set the post, re-align the hinge, and document the new position with photographs so the repair record survives long after we leave.
Gate Realignment
Santa Ana winds are a consistent seasonal factor in Burbank’s valley-mouth geography. Sliding gates on homes near the Verdugo foothills get knocked off their bottom rollers when a strong event funnels through, and wooden picket gates take a beating too. Realignment is part mechanical, part structural. We check the track, the rollers, the rack if present, and the operator’s travel limits, then adjust the gate to move cleanly through its full arc without strain.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterTrusted Brands We Service in Burbank
Most Burbank homes already have a gate motor on the property. Our job is to repair it, not sell you a different brand. We carry parts on our vans for the operators we most often see in this area, including FAAC, BFT, Linear, and Viking. If you have a FAAC swing operator on a hillside driveway off Walnut Avenue or a Linear slide motor on a studio-adjacent property, we can usually complete the repair on the first visit. The parts come with the same written price before work and the same photographed record after.
Common Gate Repair Problems We See in Burbank Homes
- Post-footing settlement on flat-lot retrofits. The 1940s to 1970s ranch homes that dominate central Burbank often had driveway gates added years after construction, with no engineered concrete footing. That leads to chronic hinge misalignment and operator overload, which reads as a “motor problem” but is actually a foundation problem under the post.
- Heat-degraded drive belts and binding ornamental iron. Burbank sits in a thermal pocket of the San Fernando Valley, routinely hitting 100°F or more in summer. Rubber belts crack, and ornamental iron expands enough that swing gates bind against their posts during the hottest hours.
- Santa Ana wind damage on hillside gates. Fall and winter wind events slam the Burbank Hills and the Verdugo foothills. Sliding gates get pushed off their bottom rollers, and wooden pickets snap on exposed hillside properties.
- Worn drive chains and failed loop detectors on studio-lot gates. Commercial gates along the Warner Bros. perimeter on Olive or the Disney campus on Buena Vista run thousands of cycles per week. Chains stretch, loop detectors fail, and the repair becomes a scheduled maintenance item rather than a surprise breakdown.
Pricing for Gate Repair in Burbank, CA
Hinge and post repair on a Burbank flat-lot gate typically runs $450 to $1,200 depending on whether the post needs new concrete or just realignment. A full gate realignment, including roller and track work, runs $250 to $600. Weld and rust repair on ornamental iron usually lands between $300 and $900. Electric gate repair, including control board diagnosis and limit switch work, runs $250 to $700. A complete slide operator replacement on a hillside driveway, including solar power integration where mains power is impractical, runs $1,800 to $3,800. You get the written price before we start, every time, under Haven Standard Clause 1. Free second opinion on any written estimate from another company, just bring the paperwork. Call (213) 577-1120 for your exact number.
We Also Serve Cities Near Burbank
While this page is for Gate Repair in Burbank, our technicians regularly cross into North Hollywood, Sun Valley, Tujunga, and Studio City. The same written-price policy and documented photo record apply everywhere we work. If your gate sits just over the city line, call us and we’ll route a technician accordingly.
Serving Burbank, CA - Our Local Coverage Area
We’re based in the Burbank area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Repair in Burbank
Because they run thousands of cycles per week instead of the few dozen a residential gate sees. A gate at a production facility near the Media District might open and close 400 times in a single day. That workload wears drive chains, stretches rack teeth, and overheats loop detectors on a predictable timeline. We treat those properties as scheduled maintenance accounts, replacing wear items before they strand a truck at the barricade. Call (213) 577-1120 to set up the same approach for your commercial gate.
Yes. We pulled a Viking slide operator off a 24-foot ranch gate in the Burbank Hills, where solar was the only practical feed and the owner needed livestock access. The gate had thrown its rack and pinion after the post footing settled. We re-set the footing, re-meshed the rack, and added a safety photocell to keep the horses from triggering a close on the gate. That job ran $2,400 for the re-footing, rack repair, photocell, and operator reinstallation. Your driveway may differ, but the approach is the same: a written price before work, and a photographed record when we leave.
Because the post was likely set in soft fill or shallow concrete decades after the original home was built, and it has been slowly rotating under the gate’s weight ever since. On 1940s to 1970s Burbank flats, we frequently find no engineered footing under retrofit gate posts. The fix is not another gate adjustment. It is re-setting the post in properly mixed concrete, then realigning the hinges so the operator no longer fights the sag. Expect $450 to $1,200 when the post needs new concrete. Call (213) 577-1120 and we’ll inspect your post before quoting anything.
Two ways. Rubber drive belts inside the operator housing dry out and crack faster in sustained 100°F-plus temperatures, and ornamental iron gates expand enough in direct sun to bind against their posts. When the gate binds, the operator overheats trying to move it, and the control board eventually trips or burns out. We replace belts and adjust travel limits with thermal expansion in mind, then photograph the new settings. The belt replacement alone typically runs $180 to $350 on a residential swing operator.
They push the gate laterally against its bottom rollers, and a strong event can lift the gate entirely off the track. Burbank’s position at the valley mouth means hillside properties near the Verdugo foothills take the brunt. We see off-track slides and snapped wooden pickets after every major wind season. The fix is re-seating the gate, checking wheel condition, and adjusting the guide posts so the next event does not repeat the same damage. A typical off-track slide gate re-seat runs $250 to $450. Call (213) 577-1120 and we’ll reset it properly, not just push it back into place.
If your gate is grinding, sagging, throwing itself off the track, or simply dead, call (213) 577-1120. A live person answers, the price is written before any work begins, and the technician who shows up at your Burbank property carries the photo record habit of a commercial access-control tech. That is the Vance difference, and it applies to every gate we touch, from a bungalow driveway off Magnolia to a credentialed studio lot on Olive.
Written by Adrian Vance, Owner at Vance Gate Repair Burbank, serving Burbank since 2014.